二，小型糖衣机机器的用途 Usage

荸荠式包衣机主要用于制药工业中压制成形的片、丸和颗粒的包衣。亦可用于食品工业中糖果机制或包衣。也可使可塑性物料滚制成丸。

抛光后的包衣片具有光亮的表面，可防止氧化、受潮或挥发，又可遮盖不适之味，使药品便于识别及缓和在人体肠胃中的溶解作用。

Our coating machine is mainly used in the pharmaceutical industry in the press-coated tablet shaped, pellets and granules. It can also be used in the food industry for nuts ,candy or snack making. It Can also rolling and polishing for special materials.

Polished coated tablets having a bright surface, prevent oxidation, moisture or volatile,covering the taste of discomfort, make it easier to identify and mitigate the drug dissolution in the stomach.

二、小型糖衣机规格与性能 Specifications:

三、结构特点及工作原理 Structure and working principle

1、结构特点：Structure

该机主要由主机和供喷液系统组成。This machine is composed by main machine and spraying system.

主机采用调速电机直接与减速机联接，减速机润滑为全封闭沉浸式润滑，油脂不易干燥，结构紧凑。操作简便，包衣转速理想。

Main machine speed frequency motor connected with the reducer directly , reducer lubrication adopts the whole closed immersion lubrication, oil is not easy to dry, compact structure. Easy to operate and ideal coating speed.

供喷液系统：供液采用由高到低自流，只要将液加到液杯中，打开下面开关，浆液就能自流至喷枪。喷枪采用日本进口雾化喷枪，喷液均匀。

Sprayer machine:The fluid flow From high to low only by adding the material into the cup and then open the following switches , then it can flow into the spray gun by taking advantage of the gravity . It adopts high spray gun to insure that it can spray evenly .

1. 工作原理：working principle

通过锅体顺时针旋转，使芯片在锅内翻滚，滑移摩擦、研磨，同时通过喷枪将包衣浆均匀喷涂到片芯上，并向锅内通以合理的热风，除去片剂表层水份，以得到合格的包衣药片。

Clockwise rotation of the pot, and spray syrup (sugar ,chocolate or other coating material) into the pot on the tablet( or nuts,snacks), and coated evenly. This machine own reasonable shape, steady linear velocity curve tablet form an optimal material flow in the pot, not only to meet the sugar-coating process requirements. But also to make the plasticised material rolled into balls and polished surface.

四、使用与保养Operation and Maintenance

1. 将主机放置平稳，再将供喷支架移至主机右侧，将喷枪放至主机衣锅内，调至合理位置。

Place the main machine stable and put the sprayer machine to the right of the main machine , make sure the spray gun is in the coating pan,and adjust to reasonable position.

1. 接通电源，打开主机调速开关，调正主机转速与旋转方向。

Connect the power,turn on the speed frequency button,adjust the rotation speed and rotation direction of the main machine.

1. 联接好气、液管给液杯加液，打开气、液开关，调整喷枪，喷液的雾幅和方向。

Connect the air,liquid pipe,and heat the liquid cup, turn on the valve of the air and liquid, adjust the spray gun ,spray width and direction

1. 将吹风机口对准锅口调整加热温度和方向。

Adjust the air blower direction and temperature.

1. 以上各工序准备完毕，确认正常无误后，停机装料，按包衣工艺进行工作。

Make sure all the steps above has been operate correctly ,you can feed in raw materials and start working

1. 使用完毕后，对机械及管路内进行清洗干净。

After working ,do not forget to clean the pipes and coating pan.